Home > Articles > Certification > CompTIA

This chapter is from the book

Troubleshooting Port Problems

Failures of the serial, parallel, and game ports tend to end with poor or no operation of the peripheral. Generally, there are only four possible causes for a problem with a device connected to an I/O port:

  • The port is defective.

  • The software is not configured properly for the port (that is, the resource allocation, speed, or protocol settings do not match).

  • The connecting signal cable is bad.

  • The attached device is not functional.

Port Problem Symptoms

Typical symptoms associated with serial, parallel, or game port failures include the following:

  • A 199, 432, or 90x IBM-compatible error code displays on the monitor (printer port).

  • The printer's Online light is on but no characters are printed when print jobs are sent to the printer.

  • An 110x IBM-compatible error code displays on the monitor (serial port error).

  • A Device Not Found error message displays, or you have an unreliable connection.

  • The input device does not work on the game port.

Basic Port Checks

With newer Pentium systems, you must check the advanced CMOS setup to determine whether the port in question has been enabled and, if so, whether it has been configured correctly. Check the PC board that contains the I/O port circuitry (and its user guide) for configuration information. This normally involves LPT, COM, and IRQ settings. Occasionally, you must set up hexadecimal addressing for the port addresses; however, this is becoming rare as PnP systems improve. For example, a modern parallel port must be enabled and set to the proper protocol type to operate advanced peripherals.

For typical printer operations, the setting can normally be set to Standard Parallel Port (SPP) mode. However, devices that use the port in a bidirectional manner need to be set to Enhanced Parallel Port (EPP) or Enhanced Capabilities Port (ECP) mode for proper operation. In both cases, the protocol must be set properly for the port and the device to carry out communications.

If serial or parallel port problems are occurring, the CMOS configuration window displayed during the startup sequence is the first place to look. Read the port assignments in the bootup window. If the system has not detected the presence of the port hardware at this stage, none of the more advanced levels will find it either. If values for any of the physical ports installed in the system do not appear in this window, check for improper port configuration.

Because the system has not loaded an operating system at the time the configuration window appears, the operating system cannot be a source of port problems at this time. If all configuration settings for the ports appear correct, assume that a hardware problem exists.

Basic Parallel Ports

Run a software diagnostic package to narrow the possible problem causes. This is not normally a problem because port failures generally do not affect the main components of the system. Software diagnostic packages normally require you to place a loopback plug in the parallel port connector to run tests on the port. The loopback plug simulates a printer device by redirecting output signals from the port into port input pins.

You can use a live printer with the port for testing purposes; however, this action elevates the possibility that the printer might inject a problem into the troubleshooting process.

If there is a printer switch box between the computer and the printer, remove the print-sharing equipment, connect the computer directly to the printer, and try to print directly to the device.

Basic Serial Ports

As with parallel ports, diagnostic packages typically ask you to place a serial loopback test plug in the serial port connector to run tests on the port. Use the diagnostic program to determine whether any IRQ or addressing conflicts exist between the serial port and other installed options. The serial loopback plug is physically wired differently from a parallel loopback plug so that it can simulate the operation of a serial device.

You can also attach a live serial device to the port for testing purposes but, like the printer, this elevates the possibility that the port might inject other problems into the troubleshooting process.

Windows Printer Checks

You can reach the I/O port functions in Windows 9x, Windows Me, and Windows 2000 through two avenues. You can access port information through the Start menu (Start, Settings). You also can reach this information through the My Computer icon on the desktop. Printer port information can be viewed through the Printers icon; serial port information is accessed through Device Manager. In Windows XP, the Printers and Faxes folder is located directly on the Start menu.

Windows Parallel Ports

Check to determine whether the Print option from the application's File menu is unavailable (gray). If so, check the My Computer, Printers window for correct parallel port settings. Be certain that the correct printer driver is selected for the printer being used. If no printer (or the wrong printer type) is selected, use the Add Printer Wizard to install and set up the desired printer.

The system's printer configuration information is also available through the Device Manager tab in the System Properties dialog box (found by double-clicking the System icon in Control Panel). Check this location for printer port setting information. Also, check the definition of the printer by double-clicking the Printer icon found in Control Panel.

The Windows operating systems come with embedded tools called troubleshooters, one of which is designed to help solve printing problems. To use the Printing Troubleshooter, access the Windows Help system through the Start menu and navigate to the Print Troubleshooter (or Printing Troubleshooter in Windows XP). The troubleshooter asks a series of questions about the printing setup. After you have answered all of its questions, the troubleshooter returns a list of recommendations for fixing the problem.

If the conclusions of the troubleshooter do not clear up the problem, try printing a document to a file. This enables you to separate the printing software from the port hardware.

Continue troubleshooting the port by checking the printer driver to ensure that it is the correct driver and version number. Right-click the Printer icon and click Properties from the shortcut menu. Click the Details tab to view the driver's name. Click the About entry under the Device Options tab to verify the driver's version number.

Click the printer port in question (after double-clicking the Printer icon) to open the Print Manager screen. Check the Print Manager for errors that have occurred and that might be holding up the printing of jobs that follow it. If an error is hanging up the print function, highlight the offending job and remove it from the print spool by clicking the Delete Document entry on the Document menu.

Windows 9x and Windows Me Serial Ports

Information on the system's serial ports is contained in three areas in Device Manager. These are the Resources entry, the Driver entry, and the Port Settings entry. The Resources entry displays port address ranges and IRQ assignments. The Driver entry displays the names of the installed device drivers and their locations. The Port Settings entry contains speed and character frame information for the serial ports. The Advanced entry under Port Settings enables you to adjust the transmit and receive buffer speeds for better operation.

Check the Device Manager window for correct serial port settings. Check the correct serial port settings under Windows 9x:

  1. Click the Port Settings option to see the setup for the ports. Most serial printers use settings of 9600 Baud, No Parity, 8 Bits, 1 Stop Bit, and Hardware Handshaking (Xon-Xoff).

  2. Click the Resources button to determine the IRQ setup for the port.

  3. Check the user's manual to document the correct settings for the device using the port in question.

USB Port Checks

Because nearly any type of peripheral device can be added to the PC through a USB port, the range of symptoms associated with a USB device can include all the symptoms listed for peripheral devices in this chapter. Therefore, problems associated with USB ports can be addressed in three general areas:

  • The USB hardware device

  • The USB controller

  • The USB drivers

As with other port types, begin troubleshooting USB port problems by checking the CMOS setup screens to ensure that the USB function is enabled there. If it is enabled in CMOS, check in Device Manager to verify that the USB controller appears there. In Windows 2000, the USB controller should be listed under the Universal Serial Bus Controllers entry, or in the Human Interface Devices entry (using the default Devices by Type setting).

If the USB controller does not appear in Device Manager, or a yellow warning icon appears next to the controller, the system's BIOS might be outdated. Contact the BIOS manufacturer for an updated copy of the BIOS.

If the controller is present in Device Manager, right-click the USB controller entry and click Properties. If any problems exist, a message appears in the device status window, shown in Figure 3.12, describing any problems and suggesting what action to take.

Figure 3.12Figure 3.12 The USB Controller Properties dialog box.

If the BIOS and controller settings appear to be correct, the next items to check are the USB port drivers. These ports have a separate entry in Device Manager that you can access by clicking the Universal Serial Bus Controllers option, right-clicking the USB Root Hub entry, and then clicking Properties.

If a USB device does not install itself automatically, you might have conflicting drivers loaded for that device and might need to remove them.

To remove potentially conflicting USB drivers, complete the following steps:

  1. Disconnect any USB devices connected to the system and start the system in safe mode.

  2. Under Windows 2000, you are asked about which operating system to use. Use the up- and down-arrow keys to highlight Windows 2000 Professional or Windows 2000 Server, and then press Enter.

  3. If alert messages appear, read each alert and then click the OK button to close it.

  4. Open Device Manager, click the desired USB device, and then click the Remove button.

  5. Your particular USB device might be listed under Universal Serial Bus Controller, Other Devices, Unknown Devices, or a particular device category (such as the Modem entry if the device is a USB modem).

  6. Click the Start menu, select the Shut Down option, select the Restart entry, and then click the OK button.

  7. Connect the USB device directly to the USB port on your computer. If the system does not autodetect the device, you must install the drivers manually. You might need drivers from the device manufacturer to perform this installation.

IEEE-1394 Adapters and Ports

Because Pentium-based PCs have largely adopted USB as the default high-speed bus, FireWire buses are implemented by installing an adapter card in the system to furnish the physical connection points. Also, there is no direct BIOS support for IEEE-1394 buses in the typical PC. However, IEEE-1394 adapter cards are plug-and-play compliant and can converse with the Windows operating systems.

The FireWire devices that attach to the bus connection do not communicate directly with the system; they work with the controller on the adapter card. Therefore, after the adapter card has been installed, you must troubleshoot it as you would any other adapter card based peripheral. The system should detect the new card when it is installed and load the driver for it automatically. If the system cannot locate the proper driver, it prompts you to supply the location where the driver can be found.

Next, you should open Device Manager to ensure the device has been recognized there and to check for conflicting device driver information (for example, an exclamation point in a yellow circle).

If Device Manager cannot see the device after the proper driver has been loaded, and the attached device has power, the final step is to check the IEEE-1394 cabling and connectors for continuity and good connections. Also verify that the correct FireWire cables are being used (a four-pin device cannot draw power through the FireWire bus). If the device employs its own power supply, verify that power is being applied to it.

If the FireWire bus runs particularly slow, and you have multiple devices attached to the system, you might have a situation in which the slower device in the middle of the chain is slowing everything down. Move the slower device (such as a Camcorder) to the end of the signal chain.

Troubleshooting Infrared Ports

The Infrared Data Association (IrDA) protocols for infrared communications specify communication ranges up to 2 meters (6 feet), but most specifications usually state 1 meter as the maximum range. All IrDA transfers are carried out in half-duplex mode and must have a clear line of sight between the transmitter and receiver. The receiver must be situated within 15 degrees of center with the line of transmission. Therefore, you should test a failing infrared connection by placing the infrared transceivers as close together as possible and straight inline with each other.

The properties of installed IrDA devices can be viewed through their entries in Device Manager. Verify that the Enable Infrared communication check box is checked. To engage support for infrared plug-and-play devices, right-click the Infrared icon on the taskbar. Verify that the Enable Plug and Play option is checked. It will only be available if the infrared and searching functions are enabled. If the taskbar icon is not visible, click the Infrared Monitor icon in Control Panel, click the Preferences tab, and select the Display the Infrared Monitor Icon on the Taskbar option.

Right-click the Infrared icon on the taskbar to install software for an infrared device. Verify that the Enable Plug and Play option is checked and verify that the new device is within range.

Windows also provides an Infrared Monitor utility that can be used to track the computer's activity. When this utility is running, it alerts you when infrared devices are within range of your computer by placing the Infrared icon on the taskbar. The Infrared Monitor not only notifies you when the computer is communicating with an infrared device, but it also indicates how well it is communicating.

InformIT Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from InformIT and its family of brands. I can unsubscribe at any time.


Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information

To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.


Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites, develop new products and services, conduct educational research and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.


If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@informit.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information

Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.


Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.


This site is not directed to children under the age of 13.


Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information

If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.


Users can always make an informed choice as to whether they should proceed with certain services offered by InformIT. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.informit.com/u.aspx.

Sale of Personal Information

Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents

California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure

Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.


This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact

Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice

We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020