Home > Articles > Certification > Cisco Certification

Hot Standby Router Protocol (HSRP) Configuration

In this article, networking consultant Sean Wilkins explains how Hot Standby Redundancy Protocol (HSRP) devices communicate together. The article then delves into the commands and configuration steps required to get HSRP up and operating between devices.
Like this article? We recommend

Once you’ve had the ability to read the first article in this series or if you have previous knowledge of Cisco’s Hot Standby Redundancy Protocol (HSRP), you should then read this article. This article takes the concepts that were covered in the initial article and offers a little more information about how the HSRP devices communicate together. It will then get into the commands and configuration steps required to get HSRP up and operating between devices.

HSRP Communications

With HSRP, three types of multicast messages are sent between the devices:

  • Hello – The hello message is sent between the active and standby devices (by default, every 3 seconds). If the standby device does not hear from the active device (via a hello message) in about 10 seconds, it will take over the active role.
  • Resign – The resign message is sent by the active HSRP device when it is getting ready to go offline or relinquish the active role for some other reason. This message tells the standby router to be ready and take over the active role.
  • Coup – The coup message is used when a standby router wants to assume the active role (preemption).

HSRP version 1 devices use the multicast IP address 224.0.0.2 to send these messages; HSRP version 2 devices use the multicast IP address 224.0.0.102.

HSRP States

When in operation, HSRP devices are configured into one of many states:

  • Active – This is the state of the device that is actively forwarding traffic.
  • Init or Disabled – This is the state of a device that is not yet ready or able to participate in HSRP.
  • Learn – This is the state of a device that has not yet determined the virtual IP address and has not yet seen a hello message from an active device.
  • Listen – This is the state of a device that is receiving hello messages.
  • Speak – This is the state of a device that is sending and receiving hello messages.
  • Standby – This is the state of a device that is prepared to take over the traffic forwarding duties from the active device.

HSRP Configuration Process and Commands

A few basic commands are used to configure HSRP on a device (see Table 1). This section goes over the commands that are required, along with a sequence that can be used to configure them. The next section will go into some examples of how HSRP can be configured.

Table 1 - HSRP Configuration Commands

1

Enter privileged EXEC mode.

router>enable

2

Enter global configuration mode.

router#configure terminal

3

Enter interface configuration mode.

router(config)#interface interface

4

Configure an IP address on the interface.

router(config-if)#ip address address netmask

5

Configure an HSRP virtual IP address.

Note: If the group-numberis not entered, then it will default to a group number of 0.

The ip-address parameter is not required but does need to be entered on at least one HSRP device. The other devices are able to learn the virtual IP address from this device.

router(config-if)#standby [group-number] ip [ip-address]

6

Configure the HSRP priority (optional).

Note: If the group-numberis not entered, then it will default to a group number of 0.

The valid values for the priorityare from 0 through 255.

router(config-if)#standby [group-number] priority priority

7

Configure HSRP preemption (optional).

router(config-if)#standby [group-number] preempt

8

Associate a tracked object to the HSRP group (optional).

Note: If the group-numberis not entered, then it will default to a group number of 0.

By default, the decrement-value is 10; what this means is that the HSRP priority will go down by 10 if the object is not ‘up’.

The shutdown parameter will disable the HSRP group if the tracked object goes down.

router(config-if)#standby [group-number] track object-number [decrement decrement-value][shutdown]

9

Create a tracked object (optional).

Note: The object-numbercan be any number between 1 and 1000.

The line-protocolparameter will track the protocol state of the configured interface. The ip routingparameter will track the IP routing capability of an interface (is it configured with an IP address and operational).

router(config)#track object-number interface interface {line-protocol | ip routing}

HSRP Configuration Example

For the example in this section, the topology shown in Figure 1 is used. HSRP is configured between two devices which each have a single interface that goes towards the core of the network, an interface that connects them together (not an HSRP requirement), and an interface that connects into a common subnet.

Figure 1 HSRP example topology

The configuration performs the following (see Tables 2 and 3):

  • Configure the IP addresses 10.10.20.1/30 (R1) and 10.10.20.2/30(R2) on their Fa0/1 interfaces.
  • Configure the IP addresses 172.16.1.1/24 (R1) and 172.16.2.1 (R2) on their Fa0/0 interfaces.
  • Configure HSRP version 2 between R1 and R2 using the IP addresses 10.10.10.1/24 (R1) and 10.10.10.2/24(R2) and a virtual IP address of 10.10.10.5 on their Fa1/0 interfaces.
  • Configure HSRP preemption on both R1 and R2.
  • Configure R1 with a HSRP priority of 140.
  • Configure the HSRP process to track the respective Fa0/0 interfaces (line-protocol) and decrement the HSRP priority by 50 should a failure occur.

Table 2 - R1 Example Configuration

1

Enter privileged EXEC mode.

R1>enable

2

Enter global configuration mode.

R1#configure terminal

3

Enter interface configuration mode.

R1(config)#interface fa0/1

4

Configure an IP address on the interface.

R1(config-if)#ip address 10.10.20.1 255.255.255.252

5

Enter interface configuration mode.

R1(config-if)#interface fa0/0

6

Configure an IP address on the interface.

R1(config-if)#ip address 172.16.1.1 255.255.255.0

7

Enter interface configuration mode.

R1(config-if)#interface fa1/0

8

Configure an IP address on the interface.

R1(config-if)#ip address 10.10.10.1 255.255.255.0

9

Configure the HSRP virtual IP address.

R1(config-if)#standby ip 10.10.10.5

10

Configure the use of HSRP version 2.

R1(config-if)#standby version 2

11

Configure the use of HSRP preemption.

R1(config-if)#standby preempt

12

Configure the HSRP priority.

R1(config-if)#standby priority 140

13

Configure HSRP object tracking.

R1(config-if)#standby track 1 decrement 50

14

Create a tracked object.

R1(config)#track 1 interface fa0/0 line-protocol

Table 3 - R2 Example Configuration

1

Enter privileged EXEC mode.

R2>enable

2

Enter global configuration mode.

R2#configure terminal

3

Enter interface configuration mode.

R2(config)#interface fa0/1

4

Configure an IP address on the interface.

R2(config-if)#ip address 10.10.20.2 255.255.255.252

5

Enter interface configuration mode.

R2(config-if)#interface fa0/0

6

Configure an IP address on the interface.

R2(config-if)#ip address 172.16.2.1 255.255.255.0

7

Enter interface configuration mode.

R2(config-if)#interface fa1/0

8

Configure an IP address on the interface.

R2(config-if)#ip address 10.10.10.2 255.255.255.0

9

Configure the HSRP virtual IP address.

R2(config-if)#standby ip 10.10.10.5

10

Configure the use of HSRP version 2.

R2(config-if)#standby version 2

11

Configure the use of HSRP preemption.

R2(config-if)#standby preempt

12

Configure HSRP object tracking.

R2(config-if)#standby track 1 decrement 50

13

Create a tracked object.

R2(config)#track 1 interface fa0/0 line-protocol

With this configuration, R1 is always the preferred active HSRP device unless its Fa0/0 interface goes down, in which case R2 will take over the active role from R1 preemptively.

Summary

This article introduced the commands that can be used to configure HSRP in a “normal” way. A number of different additional commands can be used to enable HSRP to work better in specific situations but were not covered in this article for brevity’s sake. For those seriously looking at implementing HSRP on a production network, look over Cisco’s documentation on all of the available options.

InformIT Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from InformIT and its family of brands. I can unsubscribe at any time.

Overview


Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information


To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites, develop new products and services, conduct educational research and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@informit.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information


Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security


Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children


This site is not directed to children under the age of 13.

Marketing


Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information


If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out


Users can always make an informed choice as to whether they should proceed with certain services offered by InformIT. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.informit.com/u.aspx.

Sale of Personal Information


Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents


California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure


Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links


This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact


Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice


We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020