Home > Articles

This chapter is from the book

This chapter is from the book

BIOS Setup

Most systems have the setup program built right in to the ROM BIOS software. These built-in setup programs are activated by a key sequence usually entered during the POST. Most systems show a prompt on the screen during the POST indicating which key to press to enter the BIOS Setup.

The major vendors have standardized on the following keystrokes to enter the BIOS Setup:

  • For AMI BIOS, press Del during POST.

  • For Phoenix BIOS, press F2 during POST.

  • For Award BIOS, press Del or Ctrl+Alt+Esc during POST.

  • For Microid Research BIOS, press Esc during POST.

If your system does not respond to one of these common keystroke settings, you might have to contact the manufacturer or read the system documentation to find the correct keystrokes to enter Setup.

Here are some unique ones I have encountered:

  • For IBM Aptiva/Valuepoint, press F1 during POST.

  • For Older Phoenix BIOS, boot to a Safe Mode DOS command prompt and then press Ctrl+Alt+Esc or Ctrl+Alt+S.

  • For Compaq, press F10 during POST.

After you're in the BIOS Setup main screen, you'll usually find a main menu allowing access to other menus and submenus offering various sections or screens. When you get the Setup program running, record all the settings. The easiest way to do this is to print it. If a printer is connected, press Shift+Print Screen; a copy of the screen display will be sent to the printer. Some setup programs have several pages of information, so you should record the information on each page.

Some setup programs allow for specialized control of the particular chipset used in the motherboard. These complicated settings can take up to several screens of information, which you may want to record. Most systems return these settings to a BIOS default if the CMOS battery is removed, and you lose any customized settings you might have changed.

Accessing BIOS Setup for Specific Makes and Models

This section shows some of the procedures required to enter BIOS Setup using keystrokes on specific popular laptop models.

IBM

Table 3.4 shows the methods used to run the BIOS Setup routines on all IBM ThinkPad systems.

Table 3.4 Entering BIOS Setup on IBM ThinkPads

Current ThinkPad Models

To Run BIOS Setup:

240 series 390 series 570 series i Series 1200 i Series 1300 i Series 1400 i Series 1500 i Series 172x A20, A21, A22, A30, A31 R30, R31, R32, S30, S31 T20, T21, T22, T23, T30 X20, X21, X22, X23, X24, X30, X31

Power on. Press F1 when the ThinkPad logo is displayed during startup.

TransNote

 

R40, R40e, T40

Power on. Press the blue "Access IBM" button during startup when the message "To interrupt normal startup, press the blue Access IBM button" is displayed. Then select "Start setup utility" to run the BIOS Setup Utility.

Older ThinkPad Models

To Run BIOS Setup:

300350500, 510

Press CTRL+Alt+F3 at an MS-DOS prompt. The system must be in MS- DOS mode and not in a DOS session under Windows.

310, 315310E/ED315ED

Power on. Press F2 while the ThinkPad logo is displayed during startup.

365C/CS365CD/CSD365E/ED

Press CTRL+Alt+F11 at an MS-DOS prompt. The system must be in MS-DOS mode and not in a DOS session under Windows.

365X/XD

With the unit powered off, press and hold the F1 key while powering the unit on. Continue to hold the F1 key down until Setup appears.

360, 355 series380, 385 series560 series600 series701C/CS75x series76x series770 series

With the unit powered off, press and hold the F1 key while powering the unit on. Continue to hold the F1 key down until Setup appears. On the TP 701, you can also access BIOS Setup by pressing the Fn+F1 keys atanytime.

700/C, 720/C

Power on. Press CTRL+ALT+INS when the cursor moves over to the upper-right side of the screen, right after the memory count during startup.

710T, 730T

Press and hold the suspend/resume switch while powering on the computer.


Toshiba

The methods discussed first in this section are used to run the BIOS Setup routines on Toshiba laptop systems for the following Toshiba models:

All Libretto, all Portege, Satellite 100CS, 105CS, 105CT, 110CS, 110CT, 115CS, 115CT, 1555CDS, 200CDS, 205CDS, 2060CDS, 2065CDS, 2065CDT, 2100CDS, 2100CDT, 2105CDS, 2140XCDS, 2180CDT, 2210CDT, 2210XCDS, 2250CDT, 2250XCDS, 225CDS, 2500CDT, 2505CDS, 2505CDT, 2510CDS, 2515CDS, 2530CDS, 2535CDS, 2540CDS, 2545CDS, 2590CDT, 2595CDS, 2595CDT, 2595XDVD, 2615DVD, 2655XDVD, 2675DVD, 2715DVD, 2715XDVD, 2755DVD, 2775XDVD, 300CDS, 305CDS, 305CDT, 310CDS, 310CDT, 315CDS, 315CDT, 320CDS, 320CDT, 325CDS, 325CDT, 330CDS, 330CDT, 335CDS, 335CDT, 4000CDS, 4000CDT, 4005CDS, 4005CDT, 4010CDS, 4010CDT, 4015CDS, 1805-S177, 4015CDT, 4020CDT, 4025CDT, 4030CDT, 4060CDT, 4080CDT, 4080XCDT, 4085XCDT, 1415-S115, 1415-S105, 2410-S204, 1410-S174, 2410-S203, 1410-S173, 1415-S174, 1415-S173, 1405-S172, 1405-S171, 1400-S152, 2400-S252, 2400-S202, 2400-S251, 2400-S201, 1400-S151, 2405-S202, 1405-S152, 2405-S221, 2405-S201, 1405-S151, 4090XDVD, 4100XDVD, 2800-S201, 2805-S201, T2100, T2100CS, T2100CT, T2105CS, T2105CS, T2105CT, T2110CS, T2115CS, T2130CS, T2130CT, T2150CDS, T2150CDT, T2155CDS, 2800-S202, 2805-S301, 2805-S401, 2805-S202, 2805-S302, 2805-S402, 1805-S203, 1805-S253, 1800-S203, 1800-S253, 2805-S503, 2805-S603, 2590CDS, 2590XDVD, 2695DVD, 220CDS, 2545XCDT, 1805-S273, 1805-S204, 1805-S254, 1805-S274, 1800-S204, 1800-S254, 2060CDT, 1800-S206, 1800-S256, 1805-S255, 1805-S154, 1805-S207, 1800-S207, 1800-S274, 1805-S278, 1805-S208, all Satellite Pro, all TE-Series, and all Tecra

There are three ways to run the BIOS Setup on these models:

  • From Windows, using the HWSetup program—The HWSetup program comes preinstalled on these Toshiba models, and it is also contained in the Toshiba Utilities package for these models, which can be downloaded from the Toshiba support Web site. To run HWSetup, open the Control Panel and double-click the HWSetup program. If you change any settings, you may be required to restart the system.

  • Starting with the system powered off (not in sleep/suspend or hibernate mode)—Start with the system powered off. Press the power button and then immediately press and hold the Esc key while the system runs the POST (Power On Self Test). When the POST finishes, a prompt will appear telling you to press the F1 key to enter BIOS Setup. At that time, press the F1 key to access the BIOS Setup program.

  • From MS-DOS, running the TSETUP program—TSETUP must be run under MS-DOS mode and not in a DOS session under Windows. The TSETUP utility will not work if a memory manager such as HIMEM.SYS, QEMM386, or equivalent is installed. TSETUP comes with the software provided with the system, or it can be downloaded from the Toshiba support Web site.

The next method discussed in this section is for the following Toshiba models:

Satellite 1605CDS, 1625CDT, 1675CDS, 1695CDT, 1715XCDS, 1735, 1755, 1730, 1750, 3005-S303, 3005-S403, 3000-S353, 3005-S304, 3000-S304, 3000-S307, 3005-S308, 1005-S157, 1000-S157, 1005-S158, 3005-S307, 3000-S309, 1905-S277, 1000-S158, 1200-S121, 1200-S122, 1905-S301, 1955-S801, 1955-S802, 1100-S101, 1905-S302, 1105, 1115-S103, 1905-S303, 1955-S803, 1905-S304, 1955-S804, 1110-S153, and 1115-S104

These models use a Phoenix BIOS. To access the BIOS Setup on these systems, the system must be off, and not in sleep/suspend or hibernate mode. Press the power button and then immediately press and hold down the F2 key. When the POST (Power On Self Test) finishes, the BIOS Setup screen will appear.

The final method discussed is for the following Toshiba models:

Satellite 5005-S504, 5005-S507, 5005-S508, 5105-S607, 5105-S608, 5105-S501, 5105-S701, 5105-S502, 5105-S702, 5105-S901, 5205-S503, 5205-S703, 5205-S504, and 5205-S704

These are "legacy-free" models, and they do not incorporate a BIOS Setup program in the motherboard ROM. The only way to run BIOS Setup is using a Windows-based BIOS Setup utility called HWSetup. The HWSetup utility comes preinstalled on these Toshiba models, and it is also contained in the Toshiba Utilities package for these models, which can be downloaded from the Toshiba support Web site. To run HWSetup, open the Control Panel and double-click the HWSetup program. HWSetup provides a graphical front end for modifying BIOS settings. Note that if you change any settings, you may be required to restart the system.

Compaq

The following methods are used to run the BIOS Setup routines on Compaq laptop systems:

  • For Presario models, power on the system and press F2 to enter BIOS Setup when the logo screen appears during startup.

  • For Evo models, power on the system and press F10 while the "F10 = ROM Based Setup" message is displayed in the lower-left corner of the screen during startup.

  • For Prosignia models, power on the system and press F10 when the blinking cursor appears in the upper-right corner of the display during startup.

Dell, Gateway, and Others

To run the BIOS Setup routines on Dell, Gateway, Sony, Acer, MPC, FOSA, and most other laptop systems, power on the system and then press F2 to enter BIOS Setup when the logo screen appears during startup.

Running the BIOS Setup Program (CMOS Setup)

After everything is reassembled, you can power up the system and run the BIOS Setup program. This enables you to configure the motherboard to access the installed devices and set the system date and time. The system also tests itself to determine whether any problems exists. Here are the steps to follow:

  1. Power on the system. Observe the operation via the screen and listen for any beeps from the system speaker.

  2. The system should automatically go through a Power On Self Test (POST) consisting of video BIOS checking, a RAM test, and usually an installed component report. If a fatal error occurs during the POST, you might not see anything onscreen, and the system might beep several times, indicating a specific problem. Check the motherboard or the BIOS documentation to determine what the beep codes mean.

  3. If there are no fatal errors, you should see the POST display onscreen. Depending on the type of motherboard BIOS, such as Phoenix, AMI, Award, or others, you must press a key or series of keys to interrupt the normal boot sequence and get to the Setup program screens that enable you to enter important system information. Normally, the system indicates via the onscreen display which key to press to activate the BIOS setup program during the POST, but if it doesn't, check the manual for the key(s) to press to enter the BIOS setup. Common keys used to enter BIOS Setup are F1, F2, F10, Esc, Ins, and Del.

  4. After the Setup program is running, use the Setup program menus to enter the current date and time, your hard drive settings, floppy drive types, video cards, keyboard settings, and so on. Most newer BIOSes can autodetect the hard drive, so you should not have to manually enter any parameters for it.

  5. Entering the hard drive information is the most critical when building a new system. Most modern BIOSes feature an autodetect or auto-type setting for the drive; I recommend you choose that if it is available. This causes the BIOS to read the parameters directly from the drive, which eliminates a chance for errors—especially if the builder is less experienced. These parameters include CHS (Cylinder Head Sector) specifications and transfer speed and translation settings. Most systems also let you set a user-definable type, which means that the cylinder, head, and sector counts for this type were entered manually and are not constant. If you set a user-definable type (not normally recommended unless you don't have "auto" as a choice), it is especially important that you write down the exact settings you use because this information might be very difficult to figure out if it is ever lost.

  6. Modern ATA drives also have additional configuration items that you should record. These include the translation mode and transfer speed setting. With drives larger than 528MB, you should record the translation mode, which is expressed differently in different BIOS versions. Look for a setting such as CHS, ECHS (Extended CHS), Large (which equals ECHS), or LBA (Logical Block Addressing). Typically, you set LBA or Large for any drive over 528MB. Whatever you set, it should be recorded because changing this setting after the drive has been formatted can cause problems.

  7. After you have checked over all the settings in the BIOS Setup, follow the instructions on the screen or in the motherboard manual to save the settings and exit the Setup menu.

InformIT Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from InformIT and its family of brands. I can unsubscribe at any time.

Overview


Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information


To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites, develop new products and services, conduct educational research and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@informit.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information


Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security


Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children


This site is not directed to children under the age of 13.

Marketing


Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information


If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out


Users can always make an informed choice as to whether they should proceed with certain services offered by InformIT. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.informit.com/u.aspx.

Sale of Personal Information


Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents


California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure


Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links


This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact


Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice


We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020