Home > Articles

This chapter is from the book

This chapter is from the book

Physical Ethernet Standards

Objective: Describe the components of network devices

Have I said that ethernet is the most popular LAN protocol? Ethernet started in the 1970s when Xerox needed a networking system to connect personal computers. Xerox joined forces with Digital Equipment Corp. (DEC) and Intel to develop the protocol, which is why the very first ethernet standards were referred to as DIX Ethernet. This section covers the progression of ethernet standards from the earlier 10Mbps connections to the more recent 10 gigabit ethernet connections.

Each standard has a maximum connection length and speed. Individual ethernet standards also specify which cables and connectors can be used for network connectivity. You will be introduced to each group of standards starting with the 10Mbps ethernet connections, then the 100Mbps Fast Ethernet connections, 1Gbps ethernet, and 10Gbps ethernet connections.

Ethernet

The IEEE 802.3 ethernet standards are covered in the following sections. The following list contains all the ethernet standards that are covered in this chapter, in order.

  • 10BASE-2
  • 10BASE-5
  • 10BASE-T
  • 10BASE-FL
  • 100BaseT4
  • 100BaseTX
  • 100BaseFX
  • 1000BaseT
  • 1000BaseTX
  • 1000BaseCX
  • 1000BaseSX
  • 1000BaseLX
  • 10GbE

10BASE-2

10BASE-2 networks are connected with RG-58 coaxial cables that use Bayonet Neill Concelman (BNC) connectors. There are no other hardware devices such as hubs or switches to connect devices, just the coaxial cables. This creates a physical bus topology. An electrical signal is sent by each device that wants to transmit data on that network. If more than one device sends a signal at the same time, this causes a collision and the signal is lost. To prevent loss of data transmissions, an algorithm called Carrier Sense Multiple Access Collision Detection (CSMA/CD) was defined. This algorithm sends a jam signal to notify the devices that there has been a collision. The devices then halt transmission for a random back-off time. CSMA/CD must be activated for 10Base ethernet LANs that are connected with a hub.

The name 10BASE-2 breaks down as follows:

  • 10—10Mbps data transmission speed
  • Base—Represents baseband, the signaling mode where the media can only send one signal per wire at a time
  • 2—Actually refers to 185m or the maximum segment length (where 185 is rounded up to 200 and 2 is a multiple of 100m)

10BASE-5

10BASE-5 has the same characteristics as 10BASE-2, but with a maximum segment length of 500m. The 5 is also a multiple of 100m.

10BASE-T

10BASE-T has a maximum segment length of 100m and has a 10Mbps data transmission speed. 10BASE-T can use Category 3, 4, or 5 unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cables for connectivity. If you recall, UTP is the more common and cost-effective solution. STP has an additional shield that provides additional reduction of interference and attenuation, but it is also the more expensive solution. The following cables can be used with a 10BASE-T connection:

  • Category 3—Data cable that can handle speeds up to 10Mbps.
  • Although it is faster than the Cat2 cable, this was quite popular until network speeds surpassed the 10Mbps threshold.

  • Category 4—Data cable that can handle speeds up to 16Mbps and is meant to be used with token ring LANs.
  • Category 5—Data cable that can handle speeds up to 100Mbps and is currently the most popular cable selection.

10BASE-FL

10BASE-FL also has a 10Mbps data transmission speed, but it runs over fiber-optic cables. This option allows for a maximum segment length up to 2km.

Table 3.4 compares the 802.3 ethernet characteristics, listing the key characteristics of each specification.

Table 3.4 Summary of Ethernet 802.3 Characteristics

Standard

Speed

Maximum Distance

Media Type

Connector Used

10BASE-2

10Mbps

185m

RG-58 coaxial

BNC

10BASE-5

10Mbps

500m

RG-58 coaxial

BNC

10BASE-T

10Mbps

100m

Category 3, 4, or 5 UTP or STP

RJ-45

10BASE-FL

10Mbps

Up to 2km

Fiber-optic

SC or ST


As you can see, the early standards are all limited to 10Mbps. More recent ethernet specifications allow for faster data transmission speeds and are more popular for today’s networks.

Fast Ethernet

Fast Ethernet was derived for networks that needed speeds in excess of 10Mbps. The IEEE 802.3u defines standards for 100BaseT4, 100BaseTX, and 100BaseFX. You may also hear them collectively referred to as 100BaseX. Based on what you learned from the 10Base naming scheme, you would be correct to infer that the 100 represents 100Mbps. Also, all three standards are baseband like the 10Mbps family of protocols.

100BaseT4

100BaseT4 has the same characteristics as 100BaseTX except that it can use Category 3, 4, or 5 UTP or STP cables.

100BaseTX

100BaseTX, like 10BASE-T, uses either UTP or STP. Category 5 UTP cable is used with this implementation. 10BASE-T has a maximum segment length of 100m.

100BaseFX

100BaseFX uses either single-mode or multimode fiber-optic cables to connect. Multimode (MM) fiber set for half-duplex can reach a distance of 412m. Single-mode (SM) fiber set for full-duplex can reach a distance of 10,000m. SC or ST connectors can be used. The drawback, as mentioned before with fiber implementations, is the high overhead.

  • Multimode (MM) fiber—This is generally used for shorter distances and is ideal for a campus-sized network. MM also has a larger diameter of optical fiber than SM fiber.
  • Single-mode (SM) fiber—This mode is used to span longer distances. SM also allows for a higher data rate than MM and faster data transmission speeds.

REVIEW BREAK

Table 3.5 compares Fast Ethernet 802.3u standards.

Table 3.5 Comparison of Fast Ethernet 802.3u Characteristics

Standard

Speed

Maximum Distance

Media Type

Connector Used

100BaseT4

100Mbps

100m

Category 3, 4, or 5 UTP or STP

RJ-45

100BaseTX

100Mbps

100m

Category 5 UTP or STP

RJ-45

100BaseFX

100Mbps

412m with half-duplex MM fiber

Fiber-optic

SC or ST

 

 

10,000m with full-duplex SM fiber

 


Gigabit Ethernet

Gigabit Ethernet standards all have a data transmission speed of 1000Mbps (1Gbps) and use a baseband signaling mode. Gigabit Ethernet can be broken down into two IEEE standards, 802.3ab or 1000BaseT and 802.3z or 1000BaseX.

1000BaseT 802.3ab

1000BaseT or 1000BaseTX is defined by the 802.3ab standard and can reach a maximum total distance per segment of 75m. This standard uses a minimum of Category 5 UTP cable with an RJ-45 connector.

  • Category 5e—Data cable that can handle speeds up to 1Gbps; a popular choice for Gigabit Ethernet networks.
  • Category 6—Cable that was created to exceed speeds of 1Gbps.

Table 3.6 summarizes the primary points of interest that are relevant for the 1000BaseT standard.

Table 3.6 Summary of Gigabit Ethernet 802.3ab Characteristics

Standard

Speed

Maximum Distance

Media Type

Connector Used

1000BaseT or 1000BaseTX

1000Mbps or 1Gbps

75m

Category 5 UTP or higher

RJ-45


1000BaseX 802.3z

1000BaseX is the collective name for 802.3z standards 1000BaseCX, 1000BaseSX, and 1000BaseLX that have the following characteristics respectively:

  • 1000BaseCX—1000BaseCX is the unique standard in this family because it uses shielded copper wire cable with a 9-pin shielded connector instead of fiber-optic cable for connectivity. The maximum total distance per segment is a mere 25m.
  • 1000BaseSX—1000BaseSX transmits short-wavelength laser over fiber-optic cable. Either 50-micron or 62.5-micron (diameter) MM fiber can be used with this option. Lengths may vary depending on the type of MM fiber and duplex chosen for each connection as follows:
    • Half-duplex 62.5-micron MM fiber connections can reach a maximum segment length of 275m.
    • Half-duplex 50-micron MM fiber connections can reach a maximum segment length of 316m.
    • Full-duplex 62.5-micron MM fiber connections can reach a maximum segment length of 275m.
    • Full-duplex 50-micron MM fiber connections can reach a maximum segment length of 550m.

    As you can see, the 50-micron MM fiber can offer longer segment distances. The 62.5-micron MM fiber reaches the same maximum segment length of 275m regardless of the duplex.

  • 1000BaseLX—1000BaseLX transmits long-wavelength laser over fiber-optic cable. Either 50-micron or 62.5-micron (diameter) MM fiber can be used with this option. SM fiber can also be used with 1000BaseLX, which differentiates this standard from 1000BaseSX. The same MM fiber length restrictions apply based on the implementation of half- or full-duplex. The following lengths apply when SM fiber is used:
    • Half-duplex SM fiber connections can reach a maximum segment length of 316m.
    • Full-duplex SM fiber connections can reach a maximum segment length of 5000m.

    Using full-duplex SM fiber allows for a huge increase in distance. As you can imagine, this is also the more expensive option.

Table 3.7 compares Fast Ethernet 802.3z standards.

Table 3.7 Comparison of Gigabit Ethernet 802.3z Characteristics

Standard

Speed

Maximum Distance

Media Type

Connector Used

1000BaseCX

1000Mbps or 1Gbps

25m

Shielded copper wire

9-pin shielded connector

1000BaseSX

1000Mbps or 1Gbps

275m with half or full-duplex 62.5-micron MM fiber

MM fiber-optic

SC or ST

 

 

316m with half-duplex 50-micron MM fiber

 

 

 

 

550m with full-duplex 50-micron MM fiber

 

 

1000BaseLX

1000Mbps or 1Gbps

275m with half- or full-duplex 62.5-micron MM fiber

MM or SM fiber-optic

SC or ST

 

 

316m with half-duplex 50-micron MM fiber or SM fiber

 

 

 

 

550m with full-duplex 50-micron MM fiber

 

 

 

 

5000m with full-duplex SM fiber

 

 


10-Gigabit Ethernet (10GbE)

You guessed it: 1Gbps just wasn’t a fast enough option. Actually, it is just the nature of technology to constantly strive for faster speeds. Yet another new standard was defined by IEEE and labeled 802.3ae. Earlier in this chapter you saw 10BASE-2, which has data transmission speeds of 10Mbps. 10-Gigabit Ethernet transmits data at 10,000Mbps. That is quite an upgrade! IEEE 802.3ae uses 62.5-micron MM, 50-micron MM, or SM fiber-optic cabling for connectivity and a baseband signaling mode.

Long Reach Ethernet

Cisco Long Reach Ethernet (LRE) was developed to provide broadband service over existing telephone-grade or Category 1, 2, or 3 wiring. Speeds vary between 5–15Mbps and can reach a maximum segment length of up to 5000m. Cisco LRE may be a viable networking solution for a LAN or MAN that already has Category 1/2/3 cabling installed. A hotel could benefit from Cisco LRE to provide high-speed Internet or video conferencing solutions to their clientele.

InformIT Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from InformIT and its family of brands. I can unsubscribe at any time.

Overview


Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information


To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites, develop new products and services, conduct educational research and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@informit.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information


Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security


Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children


This site is not directed to children under the age of 13.

Marketing


Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information


If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out


Users can always make an informed choice as to whether they should proceed with certain services offered by InformIT. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.informit.com/u.aspx.

Sale of Personal Information


Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents


California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure


Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links


This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact


Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice


We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020