Home > Articles > Certification > Cisco Certification

Network Security Using Cisco IOS IPS

This chapter describes the functions and operations of IDS and IPS systems.
This chapter is from the book

This chapter will introduce you to:

  • The underlying IDS and IPS technology that is embedded in the Cisco host- and network-based IDS and IPS solutions
  • Cisco IOS IPS using Cisco SDM

Intrusion detection system (IDS) and intrusion prevention system (IPS) solutions form an integral part of a robust network defense solution. Maintaining secure network services is a key requirement of a profitable IP-based business. Using Cisco products and technologies as examples, this chapter defines IDS and IPS and how these systems work.

Introducing IDS and IPS

IDS and IPS work together to provide a network security solution. An IDS captures packets in real time, processes them, and can respond to threats, but works on copies of data traffic to detect suspicious activity by using signatures. This is called promiscuous mode. In the process of detecting malicious traffic, an IDS allows some malicious traffic to pass before the IDS can respond to protect the network. An IDS analyzes a copy of the monitored traffic rather than the actual forwarded packet. The advantage of operating on a copy of the traffic is that the IDS does not affect the packet flow of the forwarded traffic. The disadvantage of operating on a copy of the traffic is that the IDS cannot stop malicious traffic from single-packet attacks from reaching the target system before the IDS can apply a response to stop the attack. An IDS often requires assistance from other networking devices, such as routers and firewalls, to respond to an attack.

An IPS works inline in the data stream to provide protection from malicious attacks in real time. This is called inline mode. Unlike an IDS, an IPS does not allow packets to enter the trusted side of the network. An IPS monitors traffic at Layer 3 and Layer 4 to ensure that their headers, states, and so on are those specified in the protocol suite. However, the IPS sensor analyzes at Layer 2 to Layer 7 the payload of the packets for more sophisticated embedded attacks that might include malicious data. This deeper analysis lets the IPS identify, stop, and block attacks that would normally pass through a traditional firewall device. When a packet comes in through an interface on an IPS, that packet is not sent to the outbound or trusted interface until the packet has been determined to be clean. An IPS builds upon previous IDS technology; Cisco IPS platforms use a blend of detection technologies, including profile-based intrusion detection, signature-based intrusion detection, and protocol analysis intrusion detection.

The key to differentiating an IDS from an IPS is that an IPS responds immediately and does not allow any malicious traffic to pass, whereas an IDS allows malicious traffic to pass before it can respond.

keytopic.jpg

IDS and IPS technologies share several characteristics:

  • IDS and IPS technologies are deployed as sensors. An IDS or an IPS sensor can be any of the following devices:

    • A router configured with Cisco IOS IPS Software
    • An appliance specifically designed to provide dedicated IDS or IPS services
    • A network module installed in an adaptive security appliance, switch, or router
  • IDS and IPS technologies typically monitor for malicious activities in two spots:

    • Malicious activity is monitored at the network to detect attacks against a network, including attacks against hosts and devices, using network IDS and network IPS.
    • Malicious activity is monitored on a host to detect attacks that are launched from or on target machines, using host intrusion prevention system (HIPS). Host-based attacks are detected by reading security event logs, checking for changes to critical system files, and checking system registries for malicious entries.
  • IDS and IPS technologies generally use yes, signatures to detect patterns of misuse in network traffic, although other technologies will be introduced later in this chapter A signature is a set of rules that an IDS or IPS uses to detect typical intrusive activity. Signatures are usually chosen from a broad cross section of intrusion detection signatures, and can detect severe breaches of security, common network attacks, and information gathering.
  • IDS and IPS technologies look for the following general patterns of misuse:

    • Atomic pattern: In an atomic pattern, an attempt is made to access a specific port on a specific host, and malicious content is contained in a single packet. An IDS is particularly vulnerable to an atomic attack because until it finds the attack, malicious single packets are being allowed into the network. An IPS prevents these packets from entering at all.
    • Composite pattern: A composite pattern is a sequence of operations distributed across multiple hosts over an arbitrary period of time.

Figure 6-1 shows a sensor deployed in IDS mode and a sensor deployed in IPS mode.

Figure 6-1

Figure 6-1 IDS and IPS Operational Differences

The following are the steps that occur when an attack is launched in an environment monitored by an IDS:

  • Step 1. An attack is launched on a network that has a sensor deployed in IDS mode.
  • Step 2. The switch sends copies of all packets to the IDS sensor (configured in promiscuous mode, which is explained later in this section) to analyze the packets. At the same time, the target machine experiences the malicious attack.
  • Step 3. The IDS sensor, using a signature, matches the malicious traffic to the signature.
  • Step 4. The IDS sensor sends the switch a command to deny access to the malicious traffic.
  • Step 5. The IDS sends an alarm to a management console for logging and other management purposes.

The following are the steps that occur when an attack is launched in an environment monitored by an IPS:

  • Step 1. An attack is launched on a network that has a sensor deployed in IPS mode (configured in inline mode, which is explained later in this section).
  • Step 2. The IPS sensor analyzes the packets as soon as they come into the IPS sensor interface. The IPS sensor, using signatures, matches the malicious traffic to the signature and the attack is stopped immediately. Traffic in violation of policy can be dropped by an IPS sensor.
  • Step 3. The IPS sensor can send an alarm to a management console for logging and other management purposes.

keytopic.jpg

keytopic.jpg

Table 6-1 lists some of the advantages and limitations of deploying an IDS platform in promiscuous mode.

Table 6-1. Advantages and Limitations of Deploying an IDS in Promiscuous Mode

Advantage

Limitation

Deploying the IDS sensor does not have any impact on the network (latency, jitter, and so on).

IDS sensor response actions cannot stop the trigger packet and are not guaranteed to stop a connection. IDS response actions are typically better at stopping an attacker more than a specific attack itself.

The IDS sensor is not inline and, therefore, a sensor failure cannot affect network functionality.

IDS sensor response actions are less helpful in stopping email viruses and automated attackers such as worms.

Overrunning the IDS sensor with data does not affect network traffic; however, it does affect the capability of the IDS to analyze the data.

Users deploying IDS sensor response actions must have a well thought-out security policy combined with a good operational understanding of their IDS deployments. Users must spend time to correctly tune IDS sensors to achieve expected levels of intrusion detection.

Being out of band (OOB), IDS sensors are more vulnerable to network evasion techniques, which are the process of totally concealing an attack.

Table 6-2 lists some of the advantages and limitations of deploying an IPS platform in inline mode.

Table 6-2. Advantages and Limitations of Deploying an IPS in Inline Mode

Advantage

Limitation

You can configure an IPS sensor to perform a packet drop that can stop the trigger packet, the packets in a connection, or packets from a source IP address.

An IPS sensor must be inline and, therefore, IPS sensor errors or failure can have a negative effect on network traffic.

Being inline, an IPS sensor can use stream normalization techniques to reduce or eliminate many of the network evasion capabilities that exist.

Overrunning IPS sensor capabilities with too much traffic does negatively affect the performance of the network.

Users deploying IPS sensor response actions must have a well thought-out security policy combined with a good operational understanding of their IPS deployments.

An IPS sensor will affect network timing because of latency, jitter, and so on. An IPS sensor must be appropriately sized and implemented so that time-sensitive applications, such as VoIP, are not negatively affected.

Traffic normalization includes techniques such as fragmentation reassembly to check the validity of the transmission.

Table 6-3 summarizes some of the advantages and limitations of an IDS in promiscuous mode and an IPS in inline mode explained earlier.

Table 6-3. Summary of Advantages and Limitations of IDS and IPS Modes

Advantages

Limitations

IDS (Promiscuous Mode)

No impact on network (latency, jitter)

Response action cannot stop trigger packets

No network impact if there is a sensor failure

Correct tuning required for response actions

No network impact if there is sensor overload

Must have a well-thought out security policy

More vulnerable to network evasion techniques

IPS (Inline Mode)

Stops trigger packets

Sensor issues might affect network traffic

Can use stream normalization techniques

Sensor overloading impacts the network

Must have a well-thought out security policy

Some impact on network (latency, jitter)

Types of IDS and IPS Systems

Table 6-4 summarizes the advantages and limitations of the various types of IDS and IPS sensors available.

Table 6-4. Types of IDS and IPS Sensors

Advantages

Limitations

Signature Based

Easy configuration

No detection of unknown signatures

Fewer false positives

Initially a lot of false positives

Good signature design

Signatures must be created, updated, and tuned

Policy Based

Simple and reliable

Generic output

Customized policies

Policy must be created

Can detect unknown attacks

Anomaly Based

Easy configuration

Difficult to profile typical activity in large networks

Can detect unknown attacks

Traffic profile must be constant

Honeypot Based

Window to view attacks

Dedicated honeypot server

Distract and confuse attackers

Honeypot server must not be trusted

Slow down and avert attacks

Collect information about attack

keytopic.jpg

The sections that follow describe these IDS and IPS sensors in more detail.

Signature-Based IDS/IPS Systems

A signature-based IDS or IPS sensor looks for specific, predefined patterns (signatures) in network traffic. It compares the network traffic to a database of known attacks, and triggers an alarm or prevents communication if a match is found. The signature can be based on a single packet or a sequence of packets. New attacks that do not match a signature do not result in detection. For this reason, the signature database needs to be constantly updated.

Signature-based pattern matching is an approach that is rigid but simple to employ. In most cases, the pattern is matched against only if the suspect packet is associated with a particular service or, more precisely, destined to and from a particular port. This matching technique helps to lessen the amount of inspection done on every packet. However, it makes it more difficult for systems to deal with protocols that do not reside on well-defined ports, such as Trojan horses and their associated traffic, which can move at will.

At the initial stage of incorporating signature-based IDS or IPS, before the signatures are tuned, there can be many false positives (traffic generating an alert which is no threat for the network). After the system is tuned and adjusted to the specific network parameters, there will be fewer false positives than with the policy-based approach.

Policy-Based IDS/IPS Systems

In policy-based systems, the IDS or IPS sensor is preconfigured based on the network security policy. You must create the policies used in a policy-based IDS or IPS. Any traffic detected outside the policy will generate an alarm or will be dropped. Creating a security policy requires detailed knowledge of the network traffic and is a time-consuming task.

Policy-based signatures use an algorithm to determine whether an alarm should be fired. Often, policy-based signature algorithms are statistical evaluations of the traffic flow. For example, in a policy-based signature used to detect a port sweep, the algorithm issues an alarm when the threshold number of unique ports is scanned on a particular machine. Policy-based signature algorithms can be designed to analyze only specific types of packets (for example, SYN packets, where the SYN bit is turned on during the handshaking process at the beginning of the session).

The policy itself might require tuning. For example, you might have to adjust the threshold level of certain types of traffic so that the policy conforms to the utilization patterns on the network that it is monitoring. Polices can be used to look for very complex relationships.

Anomaly-Based IDS/IPS Systems

Anomaly-based or profile-based signatures typically look for network traffic that deviates from what is seen “normally.” The biggest issue with this methodology is that you first must define what normal is. If during the learning phase your network is the victim of an attack and you fail to identify it, the anomaly-based IPS systems will interpret that malicious traffic as normal, and no alarm will be triggered next time this same attack takes place. Some systems have hard-coded definitions of normal traffic patterns and, in this case, could be considered heuristic-based systems.

Other systems are built to learn normal traffic behavior; however, the challenge with these systems is eliminating the possibility of improperly classifying abnormal behavior as normal. Also, if the traffic pattern being learned is assumed normal, the system must contend with how to differentiate between allowable deviations, and those deviations that are not allowed or that represent attack-based traffic. Normal network traffic can be difficult to define.

The technique used by anomaly-based IDS/IPS systems is also referred as network behavior analysis or heuristics analysis.

Honeypot-Based IDS/IPS Systems

Honeypot systems use a dummy server to attract attacks. The purpose of the honeypot approach is to distract attacks away from real network devices. By staging different types of vulnerabilities in the honeypot server, you can analyze incoming types of attacks and malicious traffic patterns. You can use this analysis to tune your sensor signatures to detect new types of malicious network traffic.

Honeypot systems are used in production environments, typically by large organizations that come across as interesting targets for hackers, such as financial enterprises, governmental agencies, and so on. Also, antivirus and other security vendors tend to use them for research.

IPS Actions

When an IPS sensor detects malicious activity, it can choose from any or all the following actions:

  • Deny attacker inline: This action terminates the current packet and future packets from this attacker address for a specified period of time. The sensor maintains a list of the attackers currently being denied by the system. You can remove entries from the list or wait for the timer to expire. The timer is a sliding timer for each entry. Therefore, if attacker A is currently being denied, but issues another attack, the timer for attacker A is reset, and attacker A remains on the denied attacker list until the timer expires. If the denied attacker list is at capacity and cannot add a new entry, the packet is still denied.
  • Deny connection inline: This action terminates the current packet and future packets on this TCP flow. This is also referred to as deny flow.
  • Deny packet inline: This action terminates the packet.
  • Log attacker packets: This action starts IP logging on packets that contain the attacker address and sends an alert. This action causes an alert to be written to the event store, which is local to the IOS router, even if the produce-alert action is not selected. Produce alert is discussed later in a bullet.
  • Log pair packets: This action starts IP logging on packets that contain the attacker and victim address pair. This action causes an alert to be written to the event store, even if the produce-alert action is not selected.
  • Log victim packets: This action starts IP logging on packets that contain the victim address and sends an alert. This action causes an alert to be written to the event store, even if the produce-alert action is not selected.
  • Produce alert: This action writes the event to the event store as an alert.
  • Produce verbose alert: This action includes an encoded dump of the offending packet in the alert. This action causes an alert to be written to the event store, even if the produce-alert action is not selected.
  • Request block connection: This action sends a request to a blocking device to block this connection.
  • Request block host: This action sends a request to a blocking device to block this attacker host.
  • Request SNMP trap: This action sends a request to the notification application component of the sensor to perform Simple Network Management Protocol (SNMP) notification. This action causes an alert to be written to the event store, even if produce-alert action is not selected.
  • Reset TCP connection: This action sends TCP resets to hijack and terminate the TCP flow.

Event Monitoring and Management

Event monitoring and management can be divided into the following two needs:

  • The need for real-time event monitoring and management
  • The need to perform analysis based on archived information (reporting)

These functions can be handled by a single server, or the functions can be placed on separate servers to scale the deployment. The number of sensors that should forward alarms to a single IPS management console is a function of the aggregate number of alarms per second that are generated by those sensors.

keytopic.jpg

Experience with customer networks has shown that the number of sensors reporting to a single IPS management console should be limited to 25 or fewer. These customers use a mixture of default signature profiles and tuned signatures. The number of alarms generated by each sensor is determined by how sensitively the sensor is tuned; the more sensitive the tuning, the fewer the alarms that are generated, and the larger the number of sensors that can report to a single IPS management console.

It is essential to tune out false positives to maximize the scalability of the network IPS deployment. Sensors that are expected to generate a large number of alarms, such as those sitting outside the corporate firewall, should log in to a separate IPS management console, because the number of false alarms raised dramatically increases the noise-to-signal ratio and makes it difficult to identify otherwise valid events.

keytopic.jpg

When implementing multiple IPS management consoles, implement either separate monitoring domains or a hierarchical monitoring structure.

InformIT Promotional Mailings & Special Offers

I would like to receive exclusive offers and hear about products from InformIT and its family of brands. I can unsubscribe at any time.

Overview


Pearson Education, Inc., 221 River Street, Hoboken, New Jersey 07030, (Pearson) presents this site to provide information about products and services that can be purchased through this site.

This privacy notice provides an overview of our commitment to privacy and describes how we collect, protect, use and share personal information collected through this site. Please note that other Pearson websites and online products and services have their own separate privacy policies.

Collection and Use of Information


To conduct business and deliver products and services, Pearson collects and uses personal information in several ways in connection with this site, including:

Questions and Inquiries

For inquiries and questions, we collect the inquiry or question, together with name, contact details (email address, phone number and mailing address) and any other additional information voluntarily submitted to us through a Contact Us form or an email. We use this information to address the inquiry and respond to the question.

Online Store

For orders and purchases placed through our online store on this site, we collect order details, name, institution name and address (if applicable), email address, phone number, shipping and billing addresses, credit/debit card information, shipping options and any instructions. We use this information to complete transactions, fulfill orders, communicate with individuals placing orders or visiting the online store, and for related purposes.

Surveys

Pearson may offer opportunities to provide feedback or participate in surveys, including surveys evaluating Pearson products, services or sites. Participation is voluntary. Pearson collects information requested in the survey questions and uses the information to evaluate, support, maintain and improve products, services or sites, develop new products and services, conduct educational research and for other purposes specified in the survey.

Contests and Drawings

Occasionally, we may sponsor a contest or drawing. Participation is optional. Pearson collects name, contact information and other information specified on the entry form for the contest or drawing to conduct the contest or drawing. Pearson may collect additional personal information from the winners of a contest or drawing in order to award the prize and for tax reporting purposes, as required by law.

Newsletters

If you have elected to receive email newsletters or promotional mailings and special offers but want to unsubscribe, simply email information@informit.com.

Service Announcements

On rare occasions it is necessary to send out a strictly service related announcement. For instance, if our service is temporarily suspended for maintenance we might send users an email. Generally, users may not opt-out of these communications, though they can deactivate their account information. However, these communications are not promotional in nature.

Customer Service

We communicate with users on a regular basis to provide requested services and in regard to issues relating to their account we reply via email or phone in accordance with the users' wishes when a user submits their information through our Contact Us form.

Other Collection and Use of Information


Application and System Logs

Pearson automatically collects log data to help ensure the delivery, availability and security of this site. Log data may include technical information about how a user or visitor connected to this site, such as browser type, type of computer/device, operating system, internet service provider and IP address. We use this information for support purposes and to monitor the health of the site, identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents and appropriately scale computing resources.

Web Analytics

Pearson may use third party web trend analytical services, including Google Analytics, to collect visitor information, such as IP addresses, browser types, referring pages, pages visited and time spent on a particular site. While these analytical services collect and report information on an anonymous basis, they may use cookies to gather web trend information. The information gathered may enable Pearson (but not the third party web trend services) to link information with application and system log data. Pearson uses this information for system administration and to identify problems, improve service, detect unauthorized access and fraudulent activity, prevent and respond to security incidents, appropriately scale computing resources and otherwise support and deliver this site and its services.

Cookies and Related Technologies

This site uses cookies and similar technologies to personalize content, measure traffic patterns, control security, track use and access of information on this site, and provide interest-based messages and advertising. Users can manage and block the use of cookies through their browser. Disabling or blocking certain cookies may limit the functionality of this site.

Do Not Track

This site currently does not respond to Do Not Track signals.

Security


Pearson uses appropriate physical, administrative and technical security measures to protect personal information from unauthorized access, use and disclosure.

Children


This site is not directed to children under the age of 13.

Marketing


Pearson may send or direct marketing communications to users, provided that

  • Pearson will not use personal information collected or processed as a K-12 school service provider for the purpose of directed or targeted advertising.
  • Such marketing is consistent with applicable law and Pearson's legal obligations.
  • Pearson will not knowingly direct or send marketing communications to an individual who has expressed a preference not to receive marketing.
  • Where required by applicable law, express or implied consent to marketing exists and has not been withdrawn.

Pearson may provide personal information to a third party service provider on a restricted basis to provide marketing solely on behalf of Pearson or an affiliate or customer for whom Pearson is a service provider. Marketing preferences may be changed at any time.

Correcting/Updating Personal Information


If a user's personally identifiable information changes (such as your postal address or email address), we provide a way to correct or update that user's personal data provided to us. This can be done on the Account page. If a user no longer desires our service and desires to delete his or her account, please contact us at customer-service@informit.com and we will process the deletion of a user's account.

Choice/Opt-out


Users can always make an informed choice as to whether they should proceed with certain services offered by InformIT. If you choose to remove yourself from our mailing list(s) simply visit the following page and uncheck any communication you no longer want to receive: www.informit.com/u.aspx.

Sale of Personal Information


Pearson does not rent or sell personal information in exchange for any payment of money.

While Pearson does not sell personal information, as defined in Nevada law, Nevada residents may email a request for no sale of their personal information to NevadaDesignatedRequest@pearson.com.

Supplemental Privacy Statement for California Residents


California residents should read our Supplemental privacy statement for California residents in conjunction with this Privacy Notice. The Supplemental privacy statement for California residents explains Pearson's commitment to comply with California law and applies to personal information of California residents collected in connection with this site and the Services.

Sharing and Disclosure


Pearson may disclose personal information, as follows:

  • As required by law.
  • With the consent of the individual (or their parent, if the individual is a minor)
  • In response to a subpoena, court order or legal process, to the extent permitted or required by law
  • To protect the security and safety of individuals, data, assets and systems, consistent with applicable law
  • In connection the sale, joint venture or other transfer of some or all of its company or assets, subject to the provisions of this Privacy Notice
  • To investigate or address actual or suspected fraud or other illegal activities
  • To exercise its legal rights, including enforcement of the Terms of Use for this site or another contract
  • To affiliated Pearson companies and other companies and organizations who perform work for Pearson and are obligated to protect the privacy of personal information consistent with this Privacy Notice
  • To a school, organization, company or government agency, where Pearson collects or processes the personal information in a school setting or on behalf of such organization, company or government agency.

Links


This web site contains links to other sites. Please be aware that we are not responsible for the privacy practices of such other sites. We encourage our users to be aware when they leave our site and to read the privacy statements of each and every web site that collects Personal Information. This privacy statement applies solely to information collected by this web site.

Requests and Contact


Please contact us about this Privacy Notice or if you have any requests or questions relating to the privacy of your personal information.

Changes to this Privacy Notice


We may revise this Privacy Notice through an updated posting. We will identify the effective date of the revision in the posting. Often, updates are made to provide greater clarity or to comply with changes in regulatory requirements. If the updates involve material changes to the collection, protection, use or disclosure of Personal Information, Pearson will provide notice of the change through a conspicuous notice on this site or other appropriate way. Continued use of the site after the effective date of a posted revision evidences acceptance. Please contact us if you have questions or concerns about the Privacy Notice or any objection to any revisions.

Last Update: November 17, 2020